TD Lines, Definition
A TD Lines trendline is drawn through two TD Points. A supply trendline is
drawn between a TD Point high (Point
Ordinarily, TD Points of any level can determine TD Lines, but optionally TD
Points of less than a specified level may be disregarded in drawing lines.
Also, the number of times that a TD Point is used as the left end of a line can be
limited; in that case, any additional lower high/higher low TD Points will be
matched to earlier TD Points.
Optionally, a TD Lines can be declared
Once created, a TD Lines is extended to the right until the line is canceled,
a TD Line Breakout occurs, or the right edge of the chart is reached. The
breakout case is further subdivided into qualified and disqualified breakouts. The
user must choose whether the terminate a line when a disqualified breakout
occurs, or to continue it to the right. If a line is terminated at a disqualified
breakout. It is drawn dotted or not at all.
Grounds for cancellation of a TD Lines before TD Line Breakout are:
1. Breakout through an opposing TD Lines.
A breakout is penetration of market price through the TD Lines; that is, high
of a bar exceeds the calculated line value at that bar for a supply line, or
low of a bar is less than the line value for a demand line. A breakout is
recognized only when the price exceeds the line value by at least N ticks, for a
breakout penetration parameter N. (If price exceeds the line by less than this,
there is not breakout, and the TD Lines continues to be extended regardless of
qualification conditions.)
A breakout is qualified if one or more these conditions are true:
1. For an upside (supply breakout, the close prior to the breakout bar is a down
close (strictly less than the close preceding it). For a downside breakout,
the prior close is an up close (greater than the preceding close).
2. For an upside (Supply) breakout, the open of the breakout bar is above the TD
Lines by at least N ticks (for a parameter-assignable N), and is also above the
prior close. For a downside (demand) breakout, the open of the breakout bar
is below the TD Lines by at least N ticks, and is also below the prior close.
3. An upside (supply) breakout is qualified if the demand value is less than the
TD Lines's value at the breakout bar by at least N ticks. The demand value is
the close of the prior bar plus the difference between that close and the
lesser of the low of that prior bar and the true low of the bar preceding it. A
downside (demand) breakout is qualified if the supply value is greater than the TD
Lines' value at the breakout bar by at least N ticks (for a
parameter-assignable N). The supply value is the close of the prior bar plus the difference
between that close and the larger of the high of that prior bar and the true high
of the bar preceding it (note this difference will be negative).
If a qualified breakout occurs, the TD Lines is ended at that point, and a
horizontal price-projection line is begun at the calculated predicted price. This
line is then extended to the right until canceled or the right edge of the
chart is reached.
Grounds for cancellation of a price projection line are:
1. Breakout through an opposing TD Lines.
2. Price penetrates the projection line.
The two conditions above are always checked.
Three additional cancellation rules can be applied using the bar after a
breakout. These three rules can be individually enabled or disabled. The price
projection line is canceled if:
1. For an upside breakout, the open of the bar after the breakout bar is below
the TD Lines' value at that bar. For a downside breakout, the open of the bar
after the breakout bar is above the TD Lines' value.
2. For an upside breakout, the high of the bar after the breakout bar is less
than the breakout bar's close and the close of the bar after the breakout bar is
below the TD Lines' value at that bar. For a downside breakout, the low of the
bar after the breakout bar is greater than the breakout bar's close and the
close of the bar after the breakout bar is above the TD Lines' value at the bar.
3. For an upside breakout, the high of the bar after the breakout bar is less
than the breakout bar's high. For a downside breakout, the low the bar after the
breakout bar is greater than the breakout bar's low.